Maybe @ladytech can offer a more permanent solution. The water supply is reaching the ice maker and the filter must be good for water flow to reach the ice maker. You don’t need to use the connector. If you placed an order on ApplianceHelp.com the order is still valid and you can check on its status and make changes here on PartSelect.com. February 16 by
(see part #800 - Machine Compartment parts diagram for location). Just light and water.
If it doesn’t have continuity it should be replaced. Common solutions for: GE Refrigerator water dispenser not working 01 - Water Tube in Door is Frozen To determine if the water supply tube is frozen, disconnect the tube at the bottom of the door and blow air through it. The ice maker was still making ice so I knew it was still receiving water. THANK YOU JIM MALINOWSKI!! FT. COUNTER-DEPTH FRENCH-DOOR ICE AND WATER REFRIGERATOR BY GE APPLIANCES. Try resetting the control panel by turning off power to the refrigerator briefly. Is there some way to turn on lights there? Refrigerator - Dispenser Control Panel Not Working. Holding the lock and lights buttons worked! The supplier in the link was only selected to show you what the part looks like (note the dual valves) and where it is located.
Unplug the refrigerator or turn it off at the circuit breaker for 30 seconds to reset the control. With mine the compressor also stops during this period. I have a GE PROFILE SERIES ENERGY STAR 22.1 CU. In addition, ensure that the freezer is kept at the proper temperature. //s.eVar15 = ""; Hey LEK, just check back to see if you have fixed the issue. To determine if the water supply tube is frozen, disconnect the tube at the bottom of the door and blow air through it. The ice dispenser works and the ice maker is working. If the valve is faulty there are other suppliers online that may suit you better. It’s been two weeks now and the refrigerator is working as expected.
I like high-tech, with the best designed refrigerator for my house. Could not find your particular service guide, but did put a link to one that may help along with a couple other links that may help. Adding a certificate takes only a few moments. closetworksofnewyork. There isn’t much extra wire, you can add more wire. When you push the paddle you can hear the switch click but not a drop comes out.
Everything should be working properly. The GE refrigerator would not hold temperature and sometimes the lights in the refrigerator would turn off and it would stop dispensing water. Dean Stewart, I have looked it over and over and also stumped, could the trim be popped off to expose and screws or perhaps the interior of door has to be removed to access scres from that side, sorry not real sure on this one.
I have the Maytag refrigerator Model MFI2568AEQ, and the display is not working, I have unplugged it and plugged it back in several times, and it still doesn't work. If the water inlet valve does not have continuity, replace it. Thank you all so much, saved me $$$$$ hundreds.
Josh Bristle. // Image call I have a GE Cafe CFSP5RKBD water stopped working a few days ago now it is completely down.
Looking to get behind the socket, I was able to remove the front control panel, removed the wires from the board, but the frame behind the control board refuses to come loose. I appreciate you nudging me in the right direction. It is more likely that a single part has failed. I have same issue and flipped cuircuit breaker on and off. Make sure the cradle has been held down 2-3 minutes to allow the reservoir to fill completely. The video shows taking out the 4 screws attaching the tan board mounting plate to the main dispenser area. Board is the one on the left side on the LG about half way up (looking from the rear) from the floor. Everything was working again, but then this morning the water again would not work and the lights inside would not turn on.
These LED's are unlit as well.
I do not wish to damage it trying to get at the wiring going to the bulb socket....... what should I try? Already ordered? How do I replace the water filter in my refrigerator?
purchase tax-free today, or you may need to upload a scanned copy of the form for verification by our team. 04/05/2016 by
We've got millions of parts, hundreds of brands, and thousands of step-by-step videos— everything you need to find it, fix it and finish the job right. Verify that the water line to the refrigerator is turned on. Thank you! Unplug the refrigerator or turn it off at the circuit breaker for 30 seconds to reset the control. Two repairmen just scratched their heads. New refrigerator no light in water/ice dispenser area JUMP TO SOLUTION 07-23-2018 06:26 PM. I also triggered the ice dispenser with my wrist while testing as well. When the freezer door is opened the freezer door switch does two things, it turns on the light in the freezer and turns off the ice and water dispenser. To determine if a dispenser switch is defective, use a multimeter to test each switch for continuity. If the water pressure is sufficient, use a multimeter to test the water inlet valve for continuity. To begin, you need to log into or create an account with PartSelect. Lights are dim since I changed the filter my ice maker makes. We’ve had the GE refrigerator for roughly 5 years and never had this issue. When the bulb is good but the light is still not working, unplug the fridge and check the light socket next. When the freezer door is opened the freezer door switch does two things, it turns on the light in the freezer and turns off the ice and water dispenser.